Cisco CCDP 300-360 Practice Exam Questions,300-360 pdf | 100% Free

Latest updates Cisco CCDP Designing Cisco Wireless Enterprise Networks (WIDESIGN v1.1) 300-360 exam questions and Answers! Free sharing 300-360 pdf online download, online exam Practice test, easy to improve skills!
Get the full 300-360 exam dumps: (Total questions:168 Q&A). Year-round updates! guarantee the first attempt to pass the exam!

[PDF] Free Cisco 300-360 pdf dumps download from Google Drive:

[PDF] Free Full Cisco pdf dumps download from Google Drive:

300-360 WIDESIGN – Cisco:

Latest effective Cisco 300-360 Exam Practice Tests

Refer to the exhibit. An engineer has determined that Cisco 7925 phones are roaming between 2.4 6Hz and 5 6Hz
radios on the same access points, which results in poor audio performance Which action must the engineer take to
mitigate this issue?
A. Enable TPCv2 to normalize the RF environment.
B. Configure EDCA parameters for Voice Optimized.
C. Configure the Cisco 7925 phone to only use 5 6Hz.
D. Enable Band Select on the WLAN
Correct Answer: B

A Cisco 7925 phone at a client\\’s location is not registering with CUCM. The engineer analyzes a packet capture, sees
that the phone receives an IP, and downloads the proper configuration file from TFTP successfully. What type of
messages should the phone be sending at this point?
A. H.245
B. H.323
Correct Answer: D

Which two options describe best practices that must be completed after a wireless installation is finished? (Choose
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe
installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if
they have any problems.
E. Test all the customer\\’s wireless devices and applications to ensure they are working properly.
Correct Answer: BE

A customer is preparing to deploy a wireless network in a stadium and is identifying coverage area requirement for the
patrons in suite areas. Which two attributes are relevant to determining these coverage requirements? (Choose two.)
A. hours d operon
B. encryption type
C. authentication type
D. number of uses
E. device types
Correct Answer: CE

An engineer is assigned to assist a customer by estimating the number of access points needed to provide voice-grade
wireless coverage in a carpeted office space. How many access points should be estimated to cover this space of
roughly 38,000 square feet?
A. 17
B. 10
C. 6
D. 13
Correct Answer: D

A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna
AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or
storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey
devices and surveys several APs. Which option is the best to reduce the negative impact of the design?
A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.
Correct Answer: B

An engineer is preparing for an active site survey of a hospital and is informed that he or she should not enter any active
surgery suites. Which option describes how the engineer should address this restriction?
A. Conduct a passive wireless survey in the restricted areas.
B. Use the predictive AP placement tool on the wireless controller
C. Skip the area and estimate where to place the access points.
D. Arrange to perform survey activities after hours.
Correct Answer: A
Passive Survey
Passive surveys are surveys that are performed with a listen-only mode. The survey client never associates to the
access point (AP). Such surveys can be helpful when you look for rogue devices or you want a good gauge of downlink
coverage from the infrastructure devices.
These can be accomplished with a passive survey:

An engineer is implementing Q0S for a new wireless voice network. Which two considerations should be identified first?
(Choose two.)
A. QoS marking
B. policing
C. QoS requirements
D. data traffic usage
E. traffic classification
Correct Answer: CE

A customer has deployed an N+N redundant wireless infrastructure. In this deployment, the access points have been
salt and peppered between controllers. What configuration would be necessary to cut down on the use of mobility
tunnels for voice clients?
A. mobility anchor
B. KIS based CAC
C. media session snooping
D. re-anchor roamed voice clients
Correct Answer: D

An engineer is determining powering requirements for a P2P wireless link using Cisco Aironet 1572EC access points.
Which power method is valid for the access point?
A. 802.3af Power over Ethernet
B. Power over Cable
C. Cisco Inline Power
D. 802.3at Power over Ethernet
Correct Answer: B

An engineer receives a digital image scanned from the floor plans of a facility to be surveyed for wireless survey and
imported it into Air Magnet Pro. However, the document contains no scale. Which action can the engineer take to most
accurately calibrate the size of the floor plan in Air Magnet?
A. Mark the length of a hallway, then count the ceiling tiles, multiply that number by 2 and enter that value.
B. Zoom in and mark across a hallway, then count the floor tiles across that hallway and enter that value.
C. Zoom in and mark a doorway, then size it at 3 feet because most doorways are 36 inches.
D. Mark the entire longest dimension of the floorplan, then use Google Earth to measure the correspondingoutside
dimension and enter that value.
Correct Answer: D

A wireless engineer is hired to troubleshoot wireless network issues and discovers that the customer is using 802 11 ac
access points with 80 MHz-wide channels in a high-density environment. Which solution addresses these issues?
A. Disable RRM on the WLC.
B. Disable TPC on the WLC
C. Decrease the channel width.
D. Increase the minimum data rate supported
Correct Answer: D

When conducting a wireless survey at a customer facility, signal attenuation in an area that is surrounded by thick glass
walls is noted as 2dB. When configuring Cisco Prime Infrastructure, which obstacle should be placed in a map editor to
represent the impact the glass wall will have on the RF signal in the facility?
A. heavy door
B. thick wall
C. glass
D. light wall
Correct Answer: D

IEEE 802.llk-2008 is an amendment to IEEE 80211-2007 standard for radio resource management. A wireless engineer
is designing a wireless network to support real time applications over wireless. Which IEEE protocol must the engineer
enable on the WLC so that neighbor list radio management packets are sent to the wireless devices?
A. 802.1 1r
B. 802.1 1w
C. 802.1 1i
D. 802.1 1k
Correct Answer: D
You can optimize roaming for non-802.11k clients by generating a prediction neighbor list for each client without sending
an 802.11k neighbor list request. When prediction based roaming enables a WLAN, after each successful client
association/re-association, the same neighbor list optimization applies on the non- 802.11k client to generate and store
the neighbor list in the mobile station software data structure. Clients at different locations have different lists because
the client probes are seen with different RSSI values by the different neighbors as the clients usually probe before any
association or re-association. This list is created with the most updated probe data and predicts the next AP that the
client is likely to roam to.
Guide/Enter prise_Mobility_8-1_Deployment_Guide/Chapter-11.html

An engineer is assigned to replace an older data-grade autonomous wireless network with a Cisco controllerbased
wireless network to meet Voice over WLAN needs. The customer also wants all existing cable infrastructure to be
reused and
no new cable be specified.
How should the engineer respond to the customer\\’s requirements?
A. Implement the wireless network with the restraints and decrease the TPC neighbor threshold to increase Txpower to
provide overlapping cell coverage at sufficient SNR to provide for Voice over WLAN service.
B. Implement the wireless network with the restraints and utilize high-gain antenna to provide overlapping cellcoverage
at sufficient SNR to provide for Voice over WLAN service.
C. Inform the customer that the network will not likely function as desired and a post install survey with thepossibility of
some new cable would be recommended.
D. Inform the customer that it is not possible to provide coverage and quality for Voice over WLAN usingexisting AP
locations and an entire overbuild will be necessary.
Correct Answer: C

When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to
support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Correct Answer: A

You have a customer that is building a new campus of four 3-story buildings that you have just completed the site
survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or
in the
data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the
easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clientSSO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Correct Answer: B

An engineer is performing a predictive wireless design for a Parts Distribution Center, which requires data and location
services. Which three requirements are inputs to the design? (Choose three.)
A. access points with directional antennas
B. continuous -67 dBm coverage from one access point
C. overlapping -75 dBm coverage from three access points
D. overlapping -67 dBm coverage from two access points
E. access points in IPS mode
F. continuous -72 dBm coverage from one access point
G. access points in corners and along perimeters
Correct Answer: BCG

A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows
significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be
excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?
A. 132
B. 44
C. 11
D. 36
Correct Answer: A

Which infrastructure issue needs to be verified and potentially resolved before deploying a centralized 802.11n WLAN?
A. That all the access layer switches that the 802.11n APs will connect to support 802.3af power.
B. That all the access layer switches that the 802.11n APs will connect to contain 10/100/1000 Ethernet ports.
C. The location of application and authentication servers.
D. The proposed location for the WDS server.
E. The proposed location for the WCS.
Correct Answer: B

A customer has determined that a cable run for a low-throughput RF design is not economically feasible to install. Which
two access point modes can alleviate these customer concerns? (Choose two.)
A. bridge
B. sniffer
C. Flex+Bridge
D. FlexConnect
E. local
Correct Answer: BC

When implementing video teleconferencing over a wireless network, which three attributes should be considered when
cell planning? (Choose three.)
A. latency
B. jitter
C. throughput
D. packet loss
E. client association
F. number of users on the network
Correct Answer: ABD

An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best 802.11n
client compatibility?
B. UNII-2e
Correct Answer: E

An engineer has performed a post-deployment site survey and noticed that access points were installed in suboptimal
locations due to physical restrictions and obstacles. Which action must the engineer take to resolve this deployment
A. Set DCA Channel Assignment Method to freeze.
B. Set all Auto RE parameters to factory default
C. Set TPC maximum and minimum power levels.
D. Set static channels on all AP radios.
Correct Answer: C
Suspect poor coverage/not enough AP density — If AP transmit power is already at the maximum, you can enable the
lower data rates to allow clients to connect from farther away. This has a negative impact on performance, but it can
help the customer understand that additional APs might be necessary. https:// -guidelines-

An access point will be partially exposed to the outdoor environment in a loading dock of a factory. How should this
access point be deployed in a cost-effective manner?
A. indoor AP with an external leaky coaxial cable
B. outdoor mesh AP utilizing the 5-GHz band
C. outdoor bridge AP pointing its antenna toward the factory
D. indoor-based AP inside a NEMA-rated enclosure
Correct Answer: B
Because mesh radio waves have very high frequency in the 5-GHz band, the radio wavelength is small; therefore, the
radio waves do not travel as far as radio waves on lower frequencies, given the same amount of power. This higher
frequency range makes the mesh ideal for unlicensed use because the radio waves do not travel far unless a high-gain
antenna is used to tightly focus the radio waves in a given direction.
technology/mesh/7-0MR1/design/guide/MeshAP_70MR1 .html#wp1849065

Which two factors influence the density of APs in a data-only WLAN environment? (Choose two.)
A. Channel reuse and WLAN bandwidth
B. The type of controller chosen.
C. The defined coverage area and customer needs.
D. The number of clients that will roam through the facility.
E. The number of APs dedicated to voice services.
Correct Answer: AC

A customer has determined that aesthetics is a primary concern for their upcoming guest deployment. Which design
consideration can be leveraged to address this concern?
A. Paint the access point to cover the LED from being noticeable
B. Use enclosures to hide the wireless infrastructure in the surrounding environment
C. Deploy environmentally friendly cabling components to blend into the environment.
D. Use AIR-AP-BRACKET-1 to allow for greater mounting locations
Correct Answer: C

An engineer is deploying an outdoor Mesh network. Which four major factors should be considered? (Choose four.)
A. power
B. buildings
C. traffic lights
D. satellite dishes
E. line of sight
F. network connectivity
G. power lines
H. mounting
Correct Answer: AEFH

You are planning the coverage for wireless VoIP by using Ekahau. Which signal strength does Ekahau recommend
using for VoIP?
A. -84 dBm
B. -76 dBm
C. -67 dBm
D. -53 dBm
Correct Answer: C
Each vendor has their own recommended signal strength for a given data rate or application. For instance, one vendor
may recommend designing their VoIP solution at -67 dBm (perhaps the most widely-used value for VoIP deployment if I
had to choose one), while another may say -70 dBm. In most cases the values will differ only by a couple dB. gth/

Which two factors influence the density of APs in a data-only WLAN environment? (Choose two.)
A. the number of clients that will roam through the facility
B. the type of controller chosen
C. the defined coverage area and customer needs
D. the number of APs dedicated to voice services
E. channel reuse and WLAN bandwidth
Correct Answer: CE

We offer more ways to make it easier for everyone to learn, and YouTube is the best tool in the video. Follow channels: get more useful exam content.

Latest Cisco 300-360 YouTube videos:

This is the latest update released by the Cisco CCDP Designing Cisco Wireless Enterprise Networks (WIDESIGN v1.1) 300-360 exam questions and answers, and we share 30 exam questions and answers for free to help you improve your skills! You can download 300-360 pdf or watch the 300-360 YouTube video tutorial online! Get the full 300-360 exam dumps: (Total questions:168 Q&A). Help you pass the exam quickly!

[PDF] Free Cisco 300-360 pdf dumps download from Google Drive:

[PDF] Free Full Cisco pdf dumps download from Google Drive:

Lead4pass Promo Code 12% Off

lead4pass 300-360 dumps

We share more practical and effective exam dumps
(Cisco,Microsoft,Oracle,Citrix,Comptia…) The latest mcsa 70-697 exam dumps help you improve your skills